ZT09 Linear Actuator: 3000N, 600mm Stroke
Review ZT09 specifications: DC 29V, up to 3,000N thrust, 6–40mm/s speed and 10–600mm stroke. Check dimensions and request a configuration.
ZT09 Linear Actuator
A 29 V push-rod actuator with up to 3,000 N maximum push , a published 6–40 mm/s speed range and 10–600 mm stroke options, with a compact mounting-reference package led by a ≥140 mm minimum installation dimension. These are configuration limits, not proof that every maximum occurs together.
Start with the working load.
The 3,000 N figure is a maximum push rating. It does not establish 40 mm/s at maximum push.
Keep the published values visible, then check them as one operating point.
ZT09 publishes force, speed, stroke and duty limits independently. The page does not assume maximum push, maximum speed and maximum travel are available together because no force-versus-speed table is present in the locked source.
| Parameter | ZT09 published value | Selection note |
|---|---|---|
| Maximum push | 3,000 N | Maximum push rating; a separate pull-force value is not established in the locked record. |
| Speed | 6–40 mm/s | Published range. State the required loaded speed when requesting configuration review. |
| Stroke | 10–600 mm | Published travel range. Confirm selected travel together with force, speed and installation space. |
| Duty cycle | 10% | The local source provides the percentage but not a detailed test-time basis. |
| Input voltage | DC 29 V | Confirm power, current capacity, connector and control arrangement for the selected configuration. |
| Minimum installation dimension | ≥140 mm | Drawing-reference value; do not use it as a closed-length formula. |
| Cylinder outer diameter | Ø24 mm | Drawing-reference value. |
| Inner shaft diameter | 39 mm | Drawing-reference value. |
| Motor and gear housing height | 140.9 mm | Drawing-reference value. |
| Mounting pin holes | Ø10 mm, both clevises | Use the current drawing for final mounting release. |
| Tube width | 31 mm | Drawing-reference value. |
| Rear-clevis offsets | 15 / 32 / 77.8 / 73 mm | Recorded drawing-reference offsets; use the current drawing for final geometry. |
Scan the ZT09 package before locking the surrounding structure.
ZT09 combines a ≥140 mm minimum installation reference with model-specific shaft, tube, housing, pin and rear-clevis dimensions. The interface is illustrative and not to scale; use the current drawing for final release.
Send the actual operating point, not four independent maximums.
A useful ZT09 review starts with working load and motion direction, then adds loaded speed, travel, mounting space, duty pattern, environment, control, electrical interface and documentation requirements.
Needs confirmation before release
Specific loaded speed near maximum push, proof of a long-stroke force/speed combination, pull force, defined ingress protection, feedback device, positioning accuracy, control-box pairing, life-cycle data and model-specific compliance evidence are not established in the locked ZT09 source.
Define the ZT09 requirement in one line.
Send working load + load direction + required loaded speed + stroke + installation space + duty pattern + control / power needs + quantity . The configuration can then be checked as one operating point instead of combining unrelated endpoints.
Use the published limits as boundaries, not shortcuts.
The verified local record supports DC 29 V, 3,000 N maximum push, 6–40 mm/s published speed, 10–600 mm stroke and a 10% duty-cycle figure.
Is ZT09 rated for 3,000 N?
Yes. The local ZT09 product data lists 3,000 N as the maximum push rating. A separate pull-force value is not published in the locked source.
Can ZT09 run at 40 mm/s while pushing 3,000 N?
The available data does not establish that operating point. It lists the force maximum and speed range separately and provides no force-speed pairing table.
Is the full 600 mm stroke available with every speed and force option?
The source confirms a 10–600 mm stroke range but does not prove every stroke, force and speed endpoint can be combined.
What voltage does ZT09 use?
The locked product source specifies DC 29 V.
What mounting dimensions are documented?
The local record lists a minimum installation dimension of at least 140 mm, Ø24 mm cylinder outer diameter, 39 mm inner shaft diameter, 140.9 mm motor-and-gear housing height, Ø10 mm mounting pin holes, 31 mm tube width, and rear-clevis offsets of 15 / 32 / 77.8 / 73 mm. Use the current technical drawing for final release.
What should I send for a quote?
Send the working load, direction, loaded speed, stroke, installation space, duty pattern, environment, control/electrical requirements, documentation needs and quantity.
