ZT01 PRODUCT STORY

Built for compact linear motion.

ZT01 packages a 29V push-rod drive into a compact actuator format for projects that need controlled linear travel without jumping immediately to a larger electric-cylinder architecture.

The key engineering question is not whether each headline maximum exists independently. It is whether your working load, loaded speed, stroke, cycle and installation envelope belong to one workable configuration.

ZT01 1 ServoCylMotion 1 scaled — ZT01 / product reference image

Verified data

The numbers that define the screening range.

These are published ZT01 values and drawing-reference dimensions. They are screening limits, not proof that every endpoint can be combined.

Parameter	Published value	Selection note
Input voltage	DC 29V	Confirm the complete power and control arrangement before release.
Maximum push	6,000 N	Maximum push rating; a separate pull-force value is not published in the local source.
Speed	6–40 mm/s	Published range. Specify required loaded speed for model review.
Stroke	10–600 mm	Confirm selected stroke together with required force and speed.
Duty cycle	10%	The local source provides the percentage but not a detailed test-time basis.
Minimum installation dimension	≥150 mm	Drawing-reference value; do not use it as a stroke-to-closed-length formula.
Cylinder outer diameter	Ø24 mm	Drawing-reference value.
Pin-hole diameter	Ø10 mm	Applies to listed mounting holes in the local drawing summary.
Motor housing height	145 mm	Drawing-reference value.
Motor base width	76.8 mm	Drawing-reference value.

Configuration boundary

One operating point.
Not three maximums.

The current source confirms a 6,000 N maximum push, a speed range to 40 mm/s and stroke options to 600 mm. It does not publish a force-versus-speed pairing table or prove that every endpoint occurs together.

01

Define the actual working load.

Normal and peak load belong in the same review as travel speed.
02

Specify loaded speed, not free-travel expectation.

The published speed range alone does not establish performance at maximum push.
03

Review stroke, cycle and installation together.

Long travel and operating frequency can change the configuration decision.

ZT01 3 1 scaled — ZT01 / installation reference

Mechanical integration

Check the envelope before release.

Send the available retracted space, mounting constraints and preferred pin orientation. Final integration should use the current controlled drawing rather than dimensions inferred from page copy.

Minimum installation dimension ≥150 mm
Cylinder outer diameter Ø24 mm
Mounting pin holes Ø10 mm
Motor housing height 145 mm
Motor base width 76.8 mm

Designing the electrical architecture at the same time? Review 29V power supply options.

Model review

What engineering actually needs.

A useful inquiry describes the mechanism and operating condition. Four input groups are enough to move from a headline model to a meaningful configuration review.

Motion

Load direction, normal and peak working load, required loaded speed, and stroke.

Mechanical

Retracted envelope, mounting limits, pin orientation, and surrounding mechanism constraints.

Duty & environment

Moves per cycle, cycles per hour, on/off pattern, temperature, dust, moisture, and exposure.

System

29V supply, connector and cable needs, controls, feedback, documentation, quantity, and timeline.

Selection posture

A strong candidate—when the project stays inside the evidence.

Use this as a screening framework, not an engineering release approval.

Good starting point

The requirement aligns with the published range.

A 29V linear push drive suits the system architecture.
Required push stays at or below the 6,000 N published maximum.
Required speed and stroke sit inside the published ranges.
The mechanism can accommodate the drawing-reference envelope.

Engineering review required

The decision depends on data the headline table does not establish.

A specific loaded speed near maximum push is required.
Pull force, IP level, lifetime or positioning accuracy is decision-critical.
A particular feedback, synchronization or control interface is required.
Model-specific compliance documents are needed for release.

ZT01 FAQ

Questions that matter before release.

Is ZT01 rated for 6,000 N?

The local product data lists 6,000 N as the maximum push rating. A separate pull-force value is not published in the same source.

Can ZT01 run at 40 mm/s while pushing 6,000 N?

The available local data does not establish that operating point. It lists the force maximum and speed range independently, without a force-speed pairing table.

Is the full 600 mm stroke available with every force and speed option?

The local data confirms the 10–600 mm stroke range, but it does not prove every stroke, force and speed endpoint can be combined.

What voltage does ZT01 use?

The local product source specifies DC 29V.

What should I send for a quote?

Send working load, load direction, required loaded speed, stroke, installation envelope, cycle, environment, control requirements, electrical interface, documentation needs and quantity.

Engineering review / RFQ